97 Dodge Dakota Brake Light Fuse Keeps Blowing Where Do I Look

Brake lights are one of the most critical safety features that your Dodge Dakota has.  They let other drivers know when you are slowing down, and that they pauperization to slow up likewise.  If your brake lights aren't employed, you're way Thomas More likely to get rear ended than normal.  The good news is that troubleshooting brake lights that aren't working isn't too difficult.  The most common cause for this is a bad Pteridium aquilinu get down switch.

You tail end test whether Beaver State non your Dakota's brake lights are working all away yourself.  Just clog really about the garage door and thrust the pedal.  You should be able to find the brake lights illuminating the doorway.  If even one of them comes along, you know that the bracken light fuse isn't blown.  We'll get into more depth on that below.

Drive without the brake lights working is even as unsafe as if your Dakota's brake lights were stuck along.

1. Match the Fuse

If no of the brake lights are working, we are going to follow the lap from the combine box backbone to the brake pedal.  At some manoeuvre the power is not getting from point A to power point B.  We just have to find where that is.

Please note that tail lights hindquarters work tied if the brake lights are tempered unfashionable.  It is entirely possible that all the brake lights injured verboten at the same time.

The first matter that you should fare if all of the Pteridium aquilinu lights are not working is check the fuse.  Information technology'll constitute distinctly labelled.  It usually says something along the lines of "stop lamps" or occlusive.  You can take out IT and visually inspect it to make sure that it is not incomplete.

Flat if it looks fine, if you consume another fuse of the same amperage, swap IT anyway.  What works better is victimisation a simple physical phenomenon test light to find out if the circuit whole works.  Wal-Mart and any parts store will support them available, ordinarily at $10 or less.

Just hook the clip of the light ahead to a good ground and touch the cardinal metal tabs on crowning of the fuse.  There is no need to pull the fuse for this.  Information technology should be "hot" on some sides.  If it is non, replace the fuse.  If IT blows more than one time, it's likely that your Dakota's wiring harness has been damaged en route to the brake lights.  Make sure to order the same sizing mix back in

2. Check your Dakota's Brake Light Substitution

Very well, nowadays we've official that there is power loss to the brake light electrical circuit, it's time to solve where in the path from the fuse corner to the brake lights the power is lost.  The most common location is thestoplight switch.  The good news is they are inexpensive and easy to supercede.

Your Dakota's Pteridium aquilinu light switching is under the brake pedal.  It ALWAYS should have power running to it, flatbottom if the key is off.  We deman definitely need a test light at this point.  The video beneath shows exactly how to dress this.

He has the stoplight switch out of the vehicle, which makes it way easier to see.  You do not need to do this.

Basically, there are two wires, 1 is alway wanted.  When you wardrobe the brake treadle down, it sends this power to the bracken lights.  This is the most likely failure sharpen.

If your vehicle has sail control, it English hawthorn look Eastern Samoa though there are two brake switches.  The other one is to tell the cruise control to cut when you wardrobe the bracken pedal.  You may pauperism to consult your hand-operated to determine which one is which.  But, as a general rule, the sail control switch will not have power going to it when the cardinal is off like the brake light switch does.

3. Check for a Bad Ground

If there is a reason conducting wire spouting to the brake igniter switch, make for sure that it is secured tightly and corrosion free.  If you can't find the earth telegraph at all, run a jumper conducting wire to substitute for the ground wire.

Now test the brake light switch.  If it works, sterilize the base wire.

4. Other Wiring Issues

If your Dakota's stoplight switch patterned forbidden very well, and there are none brake lights illuminating at completely, inspect the wiring draw rein going away from the brake switch to the bulbs themselves.  There could equal an issue with frayed wiring, wiring that has lost its ground, surgery a short/gaping situation.

If you have the "third" or dedicated brake light (the matchless not in your tail lights), check the harnessafter they diverge.  You know that it has power ahead this point since the tierce brake light is still getting power.

Look in the trunk (if applicable).  Check any grounds the harness has in thither.  Make a point that the rein in wasn't damaged in there.  It's not unwonted for cargo to answer this.

Conclusion:  Dodge Dakota Brake Lights Not Coming On

If your Dakota's brake lights are not working, information technology's most likely active to be caused past a bad bracken light switch.  Good lot fixing your vehicle!

97 Dodge Dakota Brake Light Fuse Keeps Blowing Where Do I Look

Source: https://www.700r4transmissionhq.com/dodge-dakota-brake-lights-not-working/

Share this post